Product Description
Internal Structure
Technical Specifications
Component Details
High-efficiency Permanent Magnet Motor
Insulation grade F, protective grade IP55, soft start operation, stable flow rate. The constant torque range and weak magnetic range are wider, The efficiency of the permanent magnet motor is higher by 20-30% than that of the regular motor.
Integrated Frequency Converter
Adopt the top frequency system in China, with a wide range of speed regulation, and high precision. Quality stability, to ensure that the pressure transmitter signal is transmitted.
Smart Touch Controller
Superior built-in intelligence requires minimal manual operation. A high-precision color electronic screen, clear graphics display, and indication of maintenance information, fault alarms, and safety shutdown alarms.
Special Type Intake Valve
Automatic control of the opening, to ensure the engine fuel injection and lubricating oil circulation.
Ultra-low oil circuit loss, overall efficiency improvement.
Normally open solenoid valve control, emergency stop automatically closed, prevent oil injection.
Cooling System
Large heat exchange area design effectively prevents high-temperature machines and reduces oil emulsification and coking caused by high-temperature.
Excellent Air Filter
An air filter with excellent air purification capability ensures a clean air system and three-stage filtration to maximize air purification and meet standard emissions. It can remove a lot of steam and a small amount of dust gas occasions, the ultimate vacuum is up to 1 Pa.
Reliable Oil and Air Separator
Vertical tangential cyclone separation structure, complete separation of oil and air, easy replacement of cartridge, and reduced maintenance cost.
High-Quality Soundproof Cotton
Compact noise reduction housing, achieving no vibration amplitude during operation, cooperates with high-quality soundproof cotton to further improve noise reduction levels.
Iron Oil Pipe & Air Pipe System
Iron is resistant to high temperature, low temperature, and high pressure, suitable for bad working conditions, completely leak-free, and maintenance-free.
Sanzhi Screw Vacuum Pump VS Water Ring Pump
Features of Vacuum Pump
Multiple filtration
Three-stage filtration minimizes air impurities.
Energy saving
Saves 50-60% of electricity compared to traditional vacuum pumps.
Constant pressure
Constant speed pumping, solving the problem of unstable vacuum pumping.
Higher vacuum degree
The vacuum degree of the vacuum pump on the market is -0.07Mpa, our vacuum degree is -0.098Mpa.
Easy use
Simple structure, easy to install, operate, and maintain.
Packaging&Shipping
Our Advantages
1. Price advantage
Direct to provide customers with ex-factory prices, so that customers are more competitive.
2. Direct deal
All products are supplied directly from the factory and we will offer more cost-effective products.
3. OEM & ODM services
The strong production and management capacity of the factory can provide OEM/ODM service for you.
4. Customised service
We accept non-standard orders, export orders, voltage/power/pressure, etc, which can be customized. If you have demands, please contact us.
5. Accept small order
You can place a small trial order first to test the quality of our products.
6. Fast delivery
High-quality products with timely delivery.
7. Complete authorisation
For distributors, we can provide the full authorization certificate to allow you to sell our SANZHI brand products.
ABOUT US
Sanzhi (ZheJiang ) Compressor Co., Ltd is a specialist in the production of screw air compressors and screw vacuum pumps. The extensive product range includes normal pressure/low-pressure screw air compressors, permanent magnet frequency conversion screw air compressors, two-stage compression screw air compressors, screw air compressors for laser cutting, single-tank mobile screw air compressors, double-tank mobile screw air compressor, electric mobile screw air compressor, diesel mobile screw air compressor, screw vacuum pump, etc.
Our factory is located in HangZhou City, ZheJiang Province, China. We can pick you up from HangZhou International Airport to our factory, 30 kilometers in about 1 hour. Welcome to our company!
Application industry
The items are widely used in wood processing, ceramic processing, printing processing, plastic processing, food packaging, semiconductor materials, pharmaceutical industry, PET blowing industry, petrochemical industry, rubber industry, iron and steel industry, mining industry, spraying industry, tobacco industry, foam factories, brick factories, electronic factories, marine exploration, hydroelectric power stations, ships, military industries and so on.
Successful cases
FAQ
Q1. Are you a trading company or manufacturer?
A: We are a professional manufacturer of screw vacuum pumps, with more than 10 years of experience.
Q2. How do you control quality?
A: 1. The raw materials are strictly inspected.
2. Installation procedures are strictly controlled.
3. Each machine must pass at least 5 hours of continuous testing before leaving the factory.
Q3. What information must I provide to get a suitable machine?
1. How much air delivery capacity (Unit: CFM or m³/Min)
2. How much working pressure (Unit: PSI, Bar or Mpa)
3. What is the voltage and frequency of my country of residence (V/Hz)
4. Whether I need other accessories such as an air tank, filters, and/or air dryers.
Tell us the answer, we will offer a scheme for you!
Q4. What is the general unit conversion?
1Bar = 0.1Mpa = 14.5PSI
1m³/min = 35.32cfm
1KW = 1.34HP
Q5. What is the available voltage vacuum pump?
A: Sanzhi available voltage include 380v/50hz/3p, 400v/50hz/3p, 415v/50hz/3p, 220v/60hz/3p, 440v/60hz/3p, and can be customized according to your requirements.
Q6. How long is the delivery time?
A: For standard voltage,15 working days after the confirmed order. Non-standard, please contact our sales.
Q7. What’s the payment term?
A: 30% T/T in advance, 40% T/T before shipment, and 30% T/T against the B/L copy. USD and RMB can be accepted.
Q8. How about your warranty?
A: One year for the whole machine and 2 years for screw vacuum pump, except for consumable spare parts.
Q9. What about the maintenance?
A: First maintenance needs to be done after 500 hours, and then every 2000-3000 hours to do the normal maintenance, and consider the actual environment.
Q10. Can machines be run in high-temperature environment?
A: Yes, machines would run in high-temperature environment countries. Working temperature from -20° to 45°(-4ºF-113ºF).
Q11. Do you offer OEM service?
A: Yes, with a professional design team, both OEM & ODM orders are highly welcome.
Q12. How long could your vacuum pump be used?
A: Generally, more than 10 years.
Q13. Will you provide some spare parts for the machines?
A: Yes, of course.
Q14. How about your after-sales service?
A: Provide customers with installation and commissioning online instructions, and arrange our engineers to help you with training and installation.
/* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1
| After-sales Service: | Online Technology Support |
|---|---|
| Warranty: | 1 Year, 2 Year |
| Oil or Not: | Oil |
| Structure: | Screw Vacuum Pump |
| Exhauster Method: | Positive Displacement Pump |
| Vacuum Degree: | High Vacuum |
| Samples: |
US$ 25000/Piece
1 Piece(Min.Order) | |
|---|
| Customization: |
Available
|
|
|---|
How Do You Maintain and Troubleshoot Vacuum Pumps?
Maintaining and troubleshooting vacuum pumps is essential to ensure their optimal performance and longevity. Here’s a detailed explanation:
Maintenance of Vacuum Pumps:
1. Regular Inspection: Perform regular visual inspections of the pump to check for any signs of damage, leaks, or abnormal wear. Inspect the motor, belts, couplings, and other components for proper alignment and condition.
2. Lubrication: Follow the manufacturer’s guidelines for lubrication. Some vacuum pumps require regular oil changes or lubrication of moving parts. Ensure that the correct type and amount of lubricant are used.
3. Oil Level Check: Monitor the oil level in oil-sealed pumps and maintain it within the recommended range. Add or replace oil as necessary, following the manufacturer’s instructions.
4. Filter Maintenance: Clean or replace filters regularly to prevent clogging and ensure proper airflow. Clogged filters can impair pump performance and increase energy consumption.
5. Cooling System: If the vacuum pump has a cooling system, inspect it regularly for cleanliness and proper functioning. Clean or replace cooling components as needed to prevent overheating.
6. Seals and Gaskets: Check the seals and gaskets for signs of wear or leakage. Replace any damaged or worn seals promptly to maintain airtightness.
7. Valve Maintenance: If the vacuum pump includes valves, inspect and clean them regularly to ensure proper operation and prevent blockages.
8. Vibration and Noise: Monitor the pump for excessive vibration or unusual noise, which may indicate misalignment, worn bearings, or other mechanical issues. Address these issues promptly to prevent further damage.
Troubleshooting Vacuum Pump Problems:
1. Insufficient Vacuum Level: If the pump is not achieving the desired vacuum level, check for leaks in the system, improper sealing, or worn-out seals. Inspect valves, connections, and seals for leaks and repair or replace as needed.
2. Poor Performance: If the pump is not providing adequate performance, check for clogged filters, insufficient lubrication, or worn-out components. Clean or replace filters, ensure proper lubrication, and replace worn parts as necessary.
3. Overheating: If the pump is overheating, check the cooling system for blockages or insufficient airflow. Clean or replace cooling components and ensure proper ventilation around the pump.
4. Excessive Noise or Vibration: Excessive noise or vibration may indicate misalignment, worn bearings, or other mechanical issues. Inspect and repair or replace damaged or worn parts. Ensure proper alignment and balance of rotating components.
5. Motor Issues: If the pump motor fails to start or operates erratically, check the power supply, electrical connections, and motor components. Test the motor using appropriate electrical testing equipment and consult an electrician or motor specialist if necessary.
6. Excessive Oil Consumption: If the pump is consuming oil at a high rate, check for leaks or other issues that may be causing oil loss. Inspect seals, gaskets, and connections for leaks and repair as needed.
7. Abnormal Odors: Unusual odors, such as a burning smell, may indicate overheating or other mechanical problems. Address the issue promptly and consult a technician if necessary.
8. Manufacturer Guidelines: Always refer to the manufacturer’s guidelines and recommendations for maintenance and troubleshooting specific to your vacuum pump model. Follow the prescribed maintenance schedule and seek professional assistance when needed.
By following proper maintenance procedures and promptly addressing any troubleshooting issues, you can ensure the reliable operation and longevity of your vacuum pump.
How Do Vacuum Pumps Assist in Freeze-Drying Processes?
Freeze-drying, also known as lyophilization, is a dehydration technique used in various industries, including pharmaceutical manufacturing. Vacuum pumps play a crucial role in facilitating freeze-drying processes. Here’s a detailed explanation:
During freeze-drying, vacuum pumps assist in the removal of water or solvents from pharmaceutical products while preserving their structure and integrity. The freeze-drying process involves three main stages: freezing, primary drying (sublimation), and secondary drying (desorption).
1. Freezing: In the first stage, the pharmaceutical product is frozen to a solid state. Freezing is typically achieved by lowering the temperature of the product below its freezing point. The frozen product is then placed in a vacuum chamber.
2. Primary Drying (Sublimation): Once the product is frozen, the vacuum pump creates a low-pressure environment within the chamber. By reducing the pressure, the boiling point of water or solvents present in the frozen product is lowered, allowing them to transition directly from the solid phase to the vapor phase through a process called sublimation. Sublimation bypasses the liquid phase, preventing potential damage to the product’s structure.
The vacuum pump maintains a low-pressure environment by continuously removing the water vapor or solvent vapor generated during sublimation. The vapor is drawn out of the chamber, leaving behind the freeze-dried product. This process preserves the product’s original form, texture, and biological activity.
3. Secondary Drying (Desorption): After the majority of the water or solvents have been removed through sublimation, the freeze-dried product may still contain residual moisture or solvents. In the secondary drying stage, the vacuum pump continues to apply vacuum to the chamber, but at a higher temperature. The purpose of this stage is to remove the remaining moisture or solvents through evaporation.
The vacuum pump maintains the low-pressure environment, allowing the residual moisture or solvents to evaporate at a lower temperature than under atmospheric pressure. This prevents potential thermal degradation of the product. Secondary drying further enhances the stability and shelf life of the freeze-dried pharmaceutical product.
By creating and maintaining a low-pressure environment, vacuum pumps enable efficient and controlled sublimation and desorption during the freeze-drying process. They facilitate the removal of water or solvents while minimizing the potential damage to the product’s structure and preserving its quality. Vacuum pumps also contribute to the overall speed and efficiency of the freeze-drying process by continuously removing the vapor generated during sublimation and evaporation. The precise control provided by vacuum pumps ensures the production of stable and high-quality freeze-dried pharmaceutical products.
What Is the Purpose of a Vacuum Pump in an HVAC System?
In an HVAC (Heating, Ventilation, and Air Conditioning) system, a vacuum pump serves a crucial purpose. Here’s a detailed explanation:
The purpose of a vacuum pump in an HVAC system is to remove air and moisture from the refrigerant lines and the system itself. HVAC systems, particularly those that rely on refrigeration, operate under specific pressure and temperature conditions to facilitate the transfer of heat. To ensure optimal performance and efficiency, it is essential to evacuate any non-condensable gases, air, and moisture from the system.
Here are the key reasons why a vacuum pump is used in an HVAC system:
1. Removing Moisture: Moisture can be present within an HVAC system due to various factors, such as system installation, leaks, or improper maintenance. When moisture combines with the refrigerant, it can cause issues like ice formation, reduced system efficiency, and potential damage to system components. A vacuum pump helps remove moisture by creating a low-pressure environment, which causes the moisture to boil and turn into vapor, effectively evacuating it from the system.
2. Eliminating Air and Non-Condensable Gases: Air and non-condensable gases, such as nitrogen or oxygen, can enter an HVAC system during installation, repair, or through leaks. These gases can hinder the refrigeration process, affect heat transfer, and decrease system performance. By using a vacuum pump, technicians can evacuate the air and non-condensable gases, ensuring that the system operates with the designed refrigerant and pressure levels.
3. Preparing for Refrigerant Charging: Prior to charging the HVAC system with refrigerant, it is crucial to create a vacuum to remove any contaminants and ensure the system is clean and ready for optimal refrigerant circulation. By evacuating the system with a vacuum pump, technicians ensure that the refrigerant enters a clean and controlled environment, reducing the risk of system malfunctions and improving overall efficiency.
4. Leak Detection: Vacuum pumps are also used in HVAC systems for leak detection purposes. After evacuating the system, technicians can monitor the pressure to check if it holds steady. A significant drop in pressure indicates the presence of leaks, enabling technicians to identify and repair them before charging the system with refrigerant.
In summary, a vacuum pump plays a vital role in an HVAC system by removing moisture, eliminating air and non-condensable gases, preparing the system for refrigerant charging, and aiding in leak detection. These functions help ensure optimal system performance, energy efficiency, and longevity, while also reducing the risk of system malfunctions and damage.
editor by CX 2024-04-03
Leave a Reply